Reading 1820 Blogs Daily!


  • stitchin heaven
  • Page 1 of 1 ( posts )
July 5, 2021
Journeys Month 10 – Victory Block: Part 1 from If These Threads Could Talk

Welcome to Stitchin Heaven’s Journeys BOM – Month 10 Victory Block: Part 1. This month you will be using Studio 180 Design V Block tool. Sarah Furrer is my helper this month.

Unit P, V Blocks will be cut from Print 1 & Print 4.

Piecing Instructions

Step 1 – Cut the Center Triangles from Print 4 strips. Lay the strip out and fold over the end of the strip as shown. Position the V Block® tool on the strip so that the Fold Line for Center Triangle is on the fold and the bottom of the strip ...

read more
June 3, 2021
Journeys Month 9 – Corner Beam from If These Threads Could Talk

Welcome to Stitchin Heaven‘s Journeys BOM Month 9. You all have worked so hard. This month you will learn to use your Corner Beam tool. Sue Tucker & Naz are my helpers for Month 9.

You will be working with Print 1, 4 and 11 this month.

Cutting the Center Beams

Step 1 – Stack the 7” center beam squares up to 4 layers deep. Align the Center Beam Trim #1 line on your Corner Beam® tool and the 6” finished unit line (bottom edge of tool) with the raw edges of your stack of ...

read more
May 6, 2021
Journeys Month 8 – Uneven Chains 2 from If These Threads Could Talk

Welcome to Stitchin Heaven’s Journeys Block of the Month 8 – Uneven Chains 2. I know you all worked so hard last month on your Liberty Stars. You learned how to make Uneven Chains in month 1, so this month should be a breeze. We will again be using the Four Patch Square Up tool.

This month we will be using prints 6, 10 & 11

Piecing Instructions

Step 1 – Stitch your strips together into Strip Set A, Strip Set B, and Strip Sets C. Position two strips right sides together and align the long ...

read more
March 5, 2021
Journeys Month 6 – Corner Section from If These Threads Could Talk

Welcome to Stitchin Heaven’s Journeys Month 6 – Corner Section. My helper for Month 6 is Sue Tucker, of Studio 180 Design. This month you are going to learn to make the Square/Squared unit using the Square/Squared tool. You will be using Prints 1, 2 & 5. Label your fabrics and use your best cutting skills when cutting your starter squares.

Piecing Instructions

Diamond Squares

Step 1 – Lay your Print 1 strip on the mat and clean up the short edge. Locate the Center Square window template for a 6” finished unit. Place the solid ...

read more
January 5, 2021
Journeys Month 4 – Winged Nine Patch from If These Threads Could Talk

Welcome to Stitchin Heaven’s Journeys BOM Month 4 – Winged Nine Patch. My helper for Month 4 is Diane Marvin, Certified Instructor for Studio 180 Design. This month you are going to learn to make Four Patches with Frames using prints 5, 6, 7 & 9, Center Square with print 8 and Chevrons using prints 5, 6 & 11. Required tools are the Four Patch Square Up and Corner Pop.

Prints 5, 6, 7, 8, 9 and 11

Carefully follow your cutting instructions for each print using your best cutting and measuring skills.

Jackie’s Note: To keep organized when cutting ...

read more
December 7, 2020
Journeys Month 3 – Flying Geese from If These Threads Could Talk

Welcome to Stitchin Heaven’s Journeys BOM Month 3. This month you will be learning to make flying geese the Deb Tucker way, using your Wing Clipper I. My helper this month is Deb Tucker herself! As always use your best cutting, stitching and pressing skills. We will be using prints 1, 2 & 5. Carefully cut your starter squares and let’s go!

Prints 1, 2 & 5

Piecing Instructions Flying Geese Construction

Step 1 – Mark Squares. Begin with one large Print 1 square and two Print 2 and two Print 5 small squares. On the wrong side of each small ...

read more
November 5, 2020
Journeys Month 2 – Triangle Units from If These Threads Could Talk

Welcome to Stitchin Heaven’s Journeys Month 2. My helper for Month 2 is Amy Lemke, a talented graphic artist for Studio 180 Design. This month you are going to learn to make Half Square Triangles (HSTs) and Combination Units with your Tucker Trimmer I with Prints 1, 2, 5, 10, & 11. Label your fabrics and use your best cutting skills when cutting your starter squares.

Prints 1, 2, 5, 10 & 11.

Tip: I use plain paper plates and write on them what it is I have cut out. For instance, if you are new to using a Tucker Trimmer ...

read more
September 22, 2020
Getting Ready for Journey BOM Month 1 from If These Threads Could Talk

Journey’s Month 1 will start shipping September 29th. I will post the Month 1 blog on October 6th, 2020. In the meantime if you haven’t used your Four Patch Square Up tool yet watch Deb Tucker’s Four Patch Square Up Video:

read more
September 19, 2020
Quilters – Rev your Sewing Machines! from If These Threads Could Talk

Are you Ready for Journey’s BOM? We are getting close. I am shooting for Journey’s Month 1 to be posted September 29th, IF everything is in place by then. I will keep you posted (get it, LOL). The photo above is the Journey’s I made to test the pattern last Spring. It was not made with the beautiful fabrics you are getting from Stitchin Heaven & Jason Yenter.

read more
  • stitchin heaven
  • Page 1 of 1 ( 9 posts )