Reading 1820 Blogs Daily!


  • jason yenter
  • Page 1 of 1 ( posts )
June 3, 2021
Journeys Month 9 – Corner Beam from If These Threads Could Talk

Welcome to Stitchin Heaven‘s Journeys BOM Month 9. You all have worked so hard. This month you will learn to use your Corner Beam tool. Sue Tucker & Naz are my helpers for Month 9.

You will be working with Print 1, 4 and 11 this month.

Cutting the Center Beams

Step 1 – Stack the 7” center beam squares up to 4 layers deep. Align the Center Beam Trim #1 line on your Corner Beam® tool and the 6” finished unit line (bottom edge of tool) with the raw edges of your stack of ...

read more
May 6, 2021
Journeys Month 8 – Uneven Chains 2 from If These Threads Could Talk

Welcome to Stitchin Heaven’s Journeys Block of the Month 8 – Uneven Chains 2. I know you all worked so hard last month on your Liberty Stars. You learned how to make Uneven Chains in month 1, so this month should be a breeze. We will again be using the Four Patch Square Up tool.

This month we will be using prints 6, 10 & 11

Piecing Instructions

Step 1 – Stitch your strips together into Strip Set A, Strip Set B, and Strip Sets C. Position two strips right sides together and align the long ...

read more
April 2, 2021
Journeys Month 7 – Liberty Star from If These Threads Could Talk

Welcome to Stitchin Heaven’s Journey BOM – Month 7 Liberty Star. This month, you will be using the 12” markings on the Rapid Fire® Lemoyne Star tool, but you will be working with them as quarters that will be trimmed to 6½” using your Tucker Trimmer 1 before you sew them into the quilt.

Note: Some of your strip sizes are in sixteenths of an inch. These are necessary in order to equally divide the diamond into three sections. To cut the sixteenth of an inch you will see that after the sixteenth measurement there is a 1¼ ...

read more
March 5, 2021
Journeys Month 6 – Corner Section from If These Threads Could Talk

Welcome to Stitchin Heaven’s Journeys Month 6 – Corner Section. My helper for Month 6 is Sue Tucker, of Studio 180 Design. This month you are going to learn to make the Square/Squared unit using the Square/Squared tool. You will be using Prints 1, 2 & 5. Label your fabrics and use your best cutting skills when cutting your starter squares.

Piecing Instructions

Diamond Squares

Step 1 – Lay your Print 1 strip on the mat and clean up the short edge. Locate the Center Square window template for a 6” finished unit. Place the solid ...

read more
February 4, 2021
Journeys Month 5 – Homeward Bound from If These Threads Could Talk

Welcome to Stitchin Heaven’s Journeys Month 5. My helper for Month 5 is Deb Tucker, of Studio 180 Design. This month you are going to learn to make Lemoyne Star Quarters using the Rapid Fire Lemoyne Star and Tucker Trimmer I tools. You will be using Prints 7, 9 & 11. Label your fabrics and use your best cutting skills when cutting your starter squares.

Piecing Instructions

Step 1 – Organize Strips. Place Print 9 and Print 7 into two separate piles. Use Print 7 to make the A Strip Set and Print 9 to make the ...

read more
January 5, 2021
Journeys Month 4 – Winged Nine Patch from If These Threads Could Talk

Welcome to Stitchin Heaven’s Journeys BOM Month 4 – Winged Nine Patch. My helper for Month 4 is Diane Marvin, Certified Instructor for Studio 180 Design. This month you are going to learn to make Four Patches with Frames using prints 5, 6, 7 & 9, Center Square with print 8 and Chevrons using prints 5, 6 & 11. Required tools are the Four Patch Square Up and Corner Pop.

Prints 5, 6, 7, 8, 9 and 11

Carefully follow your cutting instructions for each print using your best cutting and measuring skills.

Jackie’s Note: To keep organized when cutting ...

read more
December 7, 2020
Journeys Month 3 – Flying Geese from If These Threads Could Talk

Welcome to Stitchin Heaven’s Journeys BOM Month 3. This month you will be learning to make flying geese the Deb Tucker way, using your Wing Clipper I. My helper this month is Deb Tucker herself! As always use your best cutting, stitching and pressing skills. We will be using prints 1, 2 & 5. Carefully cut your starter squares and let’s go!

Prints 1, 2 & 5

Piecing Instructions Flying Geese Construction

Step 1 – Mark Squares. Begin with one large Print 1 square and two Print 2 and two Print 5 small squares. On the wrong side of each small ...

read more
November 5, 2020
Journeys Month 2 – Triangle Units from If These Threads Could Talk

Welcome to Stitchin Heaven’s Journeys Month 2. My helper for Month 2 is Amy Lemke, a talented graphic artist for Studio 180 Design. This month you are going to learn to make Half Square Triangles (HSTs) and Combination Units with your Tucker Trimmer I with Prints 1, 2, 5, 10, & 11. Label your fabrics and use your best cutting skills when cutting your starter squares.

Prints 1, 2, 5, 10 & 11.

Tip: I use plain paper plates and write on them what it is I have cut out. For instance, if you are new to using a Tucker Trimmer ...

read more
November 2, 2020
Hidden Snowflake Block – FREE from Want It, Need It, Quilt It!

Christmas is one of my favourite times of the year. I can hardly wait to put up the tree, decorate the house and bake. I know festive etiquette rules state that Christmas decorating is not allowed before December 1st but being the rebel I am, Christmassy things start appearing in my house from Nov 1....

Read More »

read more
September 19, 2020
Quilters – Rev your Sewing Machines! from If These Threads Could Talk

Are you Ready for Journey’s BOM? We are getting close. I am shooting for Journey’s Month 1 to be posted September 29th, IF everything is in place by then. I will keep you posted (get it, LOL). The photo above is the Journey’s I made to test the pattern last Spring. It was not made with the beautiful fabrics you are getting from Stitchin Heaven & Jason Yenter.

read more
May 21, 2020
I Will Be Your Guide On This Journey from If These Threads Could Talk

Stitchin Heaven Quilt Shop is excited to announce a new collaboration of a unique BOM program from Deb Tucker (Studio 180 Design), NYT and USA Today best-selling author Marie Bostwick (Between Heaven and Texas, Hope on the Inside, and the Cobbled Court Quilt Series, including A Single Thread), Deb Luttrell (Stitchin’ Heaven), and Jason Yenter (In the Beginning Fabrics). In this 12-month program you will take your own Journeys through an exclusive novella written by Marie Bostwick. Each month you will receive a chapter from the book which is exclusive to this program. It is a page-turning tale of love ...

read more
  • jason yenter
  • Page 1 of 1 ( 11 posts )